STM32 EEPROM
C-language library for serial EEPROM on STM32. Supports Microchip's 24AAXX serial EEPROM memory with memory block organization. The library supports only DMA mode.
Access times
The time for writing 1024 words is only 4.038 seconds.

The time for reading is only 22.94 ms, it's really fast ( ಠ ͜ʖಠ)

Pins output
| Pin Nb | PINs | FUNCTIONs | LABELs |
|-------------|----------------|----------------|----------------------|
| 2 | PC13-ANTI_TAMP | GPIO_EXTI13 | B1 [Blue PushButton] |
| 16 | PA2 | USART2_TX | USART_TX |
| 17 | PA3 | USART2_RX | USART_RX |
| 21 | PA5 | GPIO_Output | LD2 [Green Led] |
| 61 | PB8 | I2C1_SCL | |
| 62 | PB9 | I2C1_SDA | |
| PERIPHERALS | MODES | FUNCTIONS | PINS |
| I2C1 | I2C | I2C1_SCL | PB8 |
| I2C1 | I2C | I2C1_SDA | PB9 |
| SYS | SysTick | SYS_VS_Systick | VP_SYS_VS_Systick |
| USART2 | Asynchronous | USART2_RX | PA3 |
| USART2 | Asynchronous | USART2_TX | PA2 |
DMA configuration
| DMA request | Stream | Direction | Priority |
|-------------|--------------|----------------------|-----------|
| I2C1_RX | DMA1_Stream0 | Peripheral to memory | Very High |
| I2C1_TX | DMA1_Stream1 | Memory To Peripheral | Very High |
Addresses for EEPROM 24AA08 memory in organization 4x256kx8bit
| Operation |
Control Code |
Block Select |
Block Select as a binary |
Read/Write |
Result in binary form |
Result in hexadecimal form |
| Write |
1010 |
0 |
000 |
0 |
10100000 |
A0 |
| Read |
1010 |
0 |
000 |
1 |
10100001 |
A1 |
| Write |
1010 |
1 |
001 |
0 |
10100010 |
A2 |
| Read |
1010 |
1 |
001 |
1 |
10100011 |
A3 |
| Write |
1010 |
2 |
010 |
0 |
10100100 |
A4 |
| Read |
1010 |
2 |
010 |
1 |
10100101 |
A5 |
| Write |
1010 |
3 |
011 |
0 |
10100110 |
A6 |
| Read |
1010 |
3 |
011 |
1 |
10100111 |
A7 |
Example of use
char memory_dump[1024] = {0}; //8kbit
char example_1 = *"T";
char example_2[] ="9A8B7C6D5E4F3G2H1I0J...............................................................................0...................................................................................................1...................................................................................................2...................................................................................................3...................................................................................................4...................................................................................................5...................................................................................................6...................................................................................................7...................................................................................................8...................................................................................................9.....................END";
EEprom_HandleTypeDef EEprom_;
uint16_t write_address[] = { 0xA0, 0xA2, 0xA4, 0xA6 };
uint16_t read_address[] = { 0xA1, 0xA3, 0xA5, 0xA7 };
EEprom_ = eeprom_init(&hi2c1, write_address, read_address,I2C_MEMADD_SIZE_8BIT, 256);
eeprom_write(&EEprom_, 0, 0x00, (uint8_t*) &example_1,sizeof(example_1));
eeprom_write_pages(&EEprom_, (uint8_t*) &example_2,sizeof(example_2));
HAL_Delay(10);
eeprom_read(&EEprom_, 0, 0x00, (uint8_t*) &memory_dump,sizeof(memory_dump));
HAL_Delay(10);
HAL_UART_Transmit(&huart2, (uint8_t*) &memory_dump, sizeof(memory_dump),0xffffff);
List of available functions
EEprom_HandleTypeDef eeprom_init(I2C_HandleTypeDef* i2c_handel,uint16_t write_address[], uint16_t read_address[], uint16_t i2c_memSize,uint16_t block_size);
HAL_StatusTypeDef eeprom_write_pages(EEprom_HandleTypeDef *eeprom,uint8_t pData[], uint16_t Size);
HAL_StatusTypeDef eeprom_write(EEprom_HandleTypeDef *eeprom,uint16_t block_select, uint16_t mem_address, uint8_t *pData,uint16_t Size);
HAL_StatusTypeDef eeprom_read(EEprom_HandleTypeDef *eeprom,uint16_t block_select, uint16_t mem_address, uint8_t *pData,uint16_t Size);