RC6502-Apple-1-Replica
An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!
- 193
- HTML
- GPL-3.0
- 5 y ago
tebl
I do electronics because LEGOs are too expensive, but sometimes my creations come with accidental smoke...
Built from tebl's public GitHub profile, Norway. Not on Take My Repo yet, so there are no posts or updates here.
An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!
A PCB being made while watching Ben Eaters "Build a 6502 computer" video series. Includes the computer itself, a standalone slow clock and an Arduino Mega shield for the bus monitor sketch..
A HW build of the MT32-PI project, allowing you to emulate a Roland MT-32 using a Raspberry Pi. Includes enough additional modules to build a MIDI-mountain as well as adapters for connecting to most things retro.
I wanted a Pi1541 module that did not feel like I was handling bare electronics, so I made one that hides most of the scary bits (no 3d-printer required).
A PCB build of Rob Smiths Amiga DrawBridge, an Arduino-based solution for reading and writing Amiga floppy disks on modern hardware. Also includes a version of Greaseweazle.
An updated version of my C64 XUM1541, this supports the newer XUM1541 firmware and comes with a few extra goodies.
I wanted a Pi1541-module that did not feel like I was handling bare electronics, so I made another that manages to hide most of the scary bits without needing a 3d-printer.
A version of the DIAG64cart, this mainly changes components for the ones I've already got and adds a lot of LEDs. It's a blinkenlight project for diagnostic usage.
An easier to solder version of the Lumafix board, components spaced out a bit more to make things easier on the beginner (mostly meaning me). Can also be used to bypass noisy signals on motherboard, wireing directly to modulator replacement.
A simple modulator replacement for Commodore 64s with "longboards", complements my Lumafix version as well adding an audio connector for second SID.
Simple PCB for building a XUM1541, a device for copying data to and from Commodore 1541 disk drives using a modern computer.
I wanted an alternative to the SD2IEC on my Commodore 64, and I almost instantly took a liking to Pi1541 software. I did however need to design a board for it and this was the end result - even includes beepers, OLEDs and two IEC connectors
An old-school remake of the ZX Interface 2 with some modern tweaks - mainly by integrating bank switching into the interface itself. Everything done with basic logic chips and components, no magic black boxes to be found anywhere!
Switchless kernal switcher for the common breadbin Commodore 64, "longboards". Reuses power LED for easier use.
An Arduino-based tape player for old school computers like the ZX Spectrum, Dragon 32 etc. Hardware is compatible with tzxduino/arduitape and Maxduino firmware.
With the RC6502-project for making an Apple 1 replica done I wanted to do something different, so I started designing a simple version of the RCA 1802-based Cosmac ELF instead.
WASD-style joystick for vintage computers. With an added Arduino Pro Micro you can use it as a USB-keyboard, so if you wanted a DIY streamdeck or Macro-keyboard - then the C64 JoyKEY can do that as well.
A recreation of the MOS KIM-1 microcomputer, the start of the Commodore-line of computers. Complete with hex keypad, six digit displays and a lot of 8-bit fun!
There are many Stereo SID boards, but this one in mine... Add a second SID of the same type or newer substitutes for adding stereo audio to your system...
Prototyping card for developing new hardware for legacy Apple ][, //e and //gs computers.
It's a tapuino, mostly because I wanted to build one. Uses an Arduino to load tapes on the good old Commodore 64.
A simple device that allows the connection of two Commodore 64 joysticks to a modern computer over USB (using an Arduino Pro Micro). The overall goal is to be able to use vintage joysticks with emulators.